MATERIAL SAFETY DATA SHEET

U.S. Department of Labor

Occupational Safety & Health Administration

SECTION I - IDENTIFIERS

MANUFACTURER: Andek Corporation

ADDRESS: 850 Glen Avenue, Moorestown, NJ 08057

TELEPHONE: (856) 786-6900 or emergency (800) 424-9300 (CHEMTREC)

TRADE NAME: Polagard FibreLastic

CHEMICAL FAMILY: Polyvinyldiene Chloride Emulsion

SECTION II - COMPOSITION

COMPONENT CAS # APPROX % TLV

Polyvinyl Diene Chloride/Ethylene Acetate 25085-46-5 51.0

Calcium Silicate 13983-17-0 5.0

Titanium Dioxide 13463-67-7 8.0

Barium Sulfate 7727-43-7 15.0

Methyl Cellulose 9004-62-0 0.1

Fungicides: MgNO2 10377-60-3

CuNO2 3251-23-8 0.1

MgC12 10034-81-8

Calcium Metasilicate 13983-17-0 4.0

Aluminum Silicate 1344-95-2 2.0

Water 7732-18-5 12.0

KNOWN CARCINOGENS OR MUTAGENS - TYPE & DEFINITION

None

SECTION III - PHYSICAL DATA

BOILING POINT (F) 220° SPECIFIC GRAVITY (H20=1) 1.4

VAPOR PRESSURE 20 PERCENT, VOLATILE BY VOLUME 34

VAPOR DENSITY (AIR=1) >1 EVAPORATION RATE (N.B.A.=1) 1

SOLUBILITY IN WATER Reducible pH (5% SLURRY) 9.5

APPEARANCE & ODOR

Opaque viscous liquid with slight ammoniacal odor.

SECTION IV - FIRE & EXPLOSION HAZARD DATA

FLASH POINT (METHOD USED): >200°F (Seta).

FLAMMABLE LIMITS: N/A

EXTINGUISHING MEDIA: N/A

SPECIAL FIRE FIGHTING PROCEDURES: N/A

UNUSUAL FIRE & EXPLOSION HAZARDS: None

HAZARDOUS DECOMPOSITION PRODUCTS: None

SECTION V - HEALTH HAZARD DATA

EFFECTS OF OVEREXPOSURE:

SKIN: May be mildly irritating to skin.

EYES: May be irritating to the eyes.

BREATHING: Mists cause irritation to the upper respiratory tract.

SWALLOWING: Although non-toxic, entry into throat may cause choking.

FIRST AID PROCEDURES:

SKIN: Wash exposed areas with soap and water.

EYES: Immediately flush eyes with clean water for 15 minutes, then contact a physician for

immediate treatment.

BREATHING: Remove victim to fresh air.

SWALLOWING: Induce vomiting. Immediately contact a physician.

SECTION VI - REACTIVITY DATA

STABILITY: Stable.

INCOMPATABILITY (MATERIALS TO AVOID): None

HAZARDOUS POLYMERIZATION: Will not occur.

CONDITIONS TO AVOID: Freezing.

SECTION VII - SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

Cover with a layer of sand or other suitable absorbent material.

WASTE DISPOSAL METHOD:

Dispose of in accordance with local, state and federal regulations.

SECTION VIII - SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION (SPECIFY TYPE): If ventilation is inadequate, use a respirator with

dust/mist/fume cartridges.

EYE PROTECTION: Splash-proof chemical goggles.

SKIN PROTECTION: Rubber gloves.

OTHER PROTECTIVE EQUIPMENT: Provide adequate ventilation.

PERSONAL HYGIENE: Wash thoroughly after using.

SECTION IX - SPECIAL PRECAUTIONS

PRECAUTIONS TO BE TAKEN IN HANDLING:

Keep container closed and protect product from freezing.

SECTION X - TRANSPORTATION INFORMATION

PROPER SHIPPING NAME: Paint

HAZARD CLASS: None

PACKING GROUP: N/A

ID #: N/A

RQ: N/A

TRANSPORT LABELS REQUIRED: This material is not regulated by the D.O.T.

This information accumulated herein is believed to be accurate but is not warranted to be, whether

originating with the company or not. Recipients are advised to confirm, in advance of need, that

the information is current, applicable and suitable to their circumstances.

DATE ISSUED: JANUARY 2005