MATERIAL SAFETY DATA SHEET

U.S. Department of Labor

Occupational Safety & Health Administration

SECTION I - IDENTIFIERS

MANUFACTURER: Andek Corporation

ADDRESS: 850 Glen Avenue, Moorestown, NJ 08057

TELEPHONE: (856) 786-6900 or emergency (800) 424-9300 (CHEMTREC)

TRADE NAME: Polajoint - Part B

CHEMICAL FAMILY: Cycloaliphatic Amine Hardener

SECTION II - COMPOSITION

COMPONENT CAS # APPROX % TLV

Polyamine Modified Fatty Amide N.O.S. (ITASCA FILE) 100

KNOWN CARCINOGENS OR MUTAGENS - TYPE & DEFINITION

NONE

SECTION III - PHYSICAL DATA

BOILING POINT (F) Decomposes SPECIFIC GRAVITY (H20=1) 1.1

VAPOR PRESSURE N/A PERCENT, VOLATILE BY VOLUME None

VAPOR DENSITY (AIR=1) N/A EVAPORATION RATE (N.B.A.=1) None

SOLUBILITY IN WATER Insoluble pH (5% slurry) 7.5

APPEARANCE & ODOR

Clear liquid with slight ammoniacal odor.

SECTION IV - FIRE & EXPLOSION HAZARD DATA

FLASH POINT (METHOD USED) : 485°F (Pensky Martens Closed Cup)

FLAMMABLE LIMITS: N/A

EXTINGUISHING MEDIA: CO², dry chemical.

SPECIAL FIRE FIGHTING PROCEDURES: Standard

UNUSUAL FIRE & EXPLOSION HAZARDS: None

DECOMPOSITION PRODUCTS: Thermal decomposition yields oxides of carbon and nitrogen.

SECTION V - HEALTH HAZARD DATA

EFFECTS OF OVEREXPOSURE:

SKIN: Prolonged or repeated contact may cause skin irritation and/or result in skin sensitization or

other allergic response.

EYES: Irritation and redness from direct eye contact

BREATHING: High temperatures may yield irritating fumes.

SWALLOWING: Low acute oral toxicity (LD50 greater than 2,000 Mg/kg for rats).

FIRST AID PROCEDURES:

SKIN: Wash thoroughly with soap and water. Launder clothes before reuse.

EYES: Irrigate with water for 15 minutes and seek medical attention.

BREATHING: Move victim to fresh air. If effects occur, consult medical personnel.

SWALLOWING: Induce vomiting if large amount ingested. Low toxicity, no specific antidote.

SECTION VI - REACTIVITY DATA

STABILITY: Stable.

INCOMPATABILITY (MATERIALS TO AVOID): Avoid strong bases.

HAZARDOUS DECOMPOSITION PRODUCTS: None under normal conditions.

HAZARDOUS POLYMERIZATION: May occur.

CONDITIONS TO AVOID: Avoid excessive heating over a long period of time. When large quantities

are mixed, high exotherm may result. Avoid mixing with water.

SECTION VII - SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:

Contain spill with absorbent material. If necessary, soak contaminated area with a 5% acetic acid and

wash with water. Clean up area may be slippery; if so, spread sand or grit.

WASTE DISPOSAL METHOD:

In accordance with local, state and federal regulations in approved metal containers.

SECTION VIII - SPECIAL PROTECTION INFORMATION

RESPIRATORY PROTECTION (SPECIFY TYPE): During mixing, a NIOSH approved dust mask should

be worn, otherwise unnecessary.

EYE PROTECTION: Safety glasses with side shields.

SKIN PROTECTION: Rubber or polyethylene gloves.

OTHER PROTECTIVE EQUIPMENT: Adequate clothing to prevent direct contact to skin.

PERSONAL HYGIENE: Wash thoroughly after use.

SECTION IX - SPECIAL PRECAUTIONS

PRECAUTIONS TO BE TAKEN IN HANDLING:

Store in a dry area away from heat. Keep container sealed until ready for use.

This information accumulated herein is believed to be accurate but is not warranted to be, whether

originating with the company or not. Recipients are advised to confirm, in advance of need, that the

information is current, applicable and suitable to their circumstances.

DATE ISSUED: JANUARY 2005