MATERIAL SAFETY DATA SHEET

U.S. Department of Labor

Occupational Safety & Health Administration

Polaprime 21
MSDS HOME

 

 

SECTION I - IDENTIFIERS                                                                                                                          

 

MANUFACTURER:     Andek Corporation

ADDRESS:                850 Glen Avenue, Moorestown, NJ 08057

TELEPHONE:            (856) 786-6900 or emergency (800) 424-9300 (CHEMTREC)

TRADE NAME:           Polaprime 2l

CHEMICAL FAMILY:   Metal Oxide Extended Urethane Prepolymer

 

SECTION II - COMPOSITION                                                                                                                      

 

COMPONENT                                                                       CAS #               APPROX %    TLV

Lampblack/Titanium Dioxide or Iron Oxide                           l3463-67-7                    11.2

Naptha Light Aromatic Solvent                                            64742-95-6                   42.3

Polyester Prepolymer Resin Solution N.O.S.                        ITASCA File)                39.9

Acrylic Resin                                                                    (ITASCA File)                  6.6

 

KNOWN CARCINOGENS OR MUTAGENS - TYPE & DEFINITION

None

 

SECTION III - PHYSICAL DATA                                                                                                                  

 

BOILING POINT (F)               312°                             SPECIFIC GRAVITY (H20=1)                0.98

VAPOR PRESSURE              10                               PERCENT, VOLATILE BY VOLUME     42.3

VAPOR DENSITY (AIR=1)     4.8                               EVAPORATION RATE (N.B.A.=1)         0.25

SOLUBILITY IN WATER        Insoluble                       pH (5% SLURRY)                                7

 

APPEARANCE & ODOR

Gray or red liquid with perfume-like odor.

 

SECTION IV - FIRE & EXPLOSION HAZARD DATA                                                                                     

 

FLASH POINT (METHOD USED):  105°F.  Closed Cup (ASTM D50).

FLAMMABLE LIMITS:  Lel 0.9; Uel 6.0.

EXTINGUISHING MEDIA:  Carbon dioxide; dry chemical; foam.

SPECIAL FIRE FIGHTING PROCEDURES:  If excessive fumes or smoke is encountered, wear self-contained

respiratory equipment and full protective clothing.

UNUSUAL FIRE & EXPLOSION HAZARDS:  Sealed containers may build up pressure if exposed to heat (fire). 

Water may be used to cool the exterior of the containers.

DECOMPOSITION PRODUCTS:  Oxides of carbon, nitrogen and iron, possible HCN and polyurethane

combustion compounds.

 

SECTION V - HEALTH HAZARD DATA                                                                                                        

 

EFFECTS OF OVEREXPOSURE:

 

SKIN:  May irritate skin.

EYES:  Contact may cause severe damage.  Vapor may irritate.

BREATHING:  Inhalation may cause headache, dizziness, nausea and irritation.

SWALLOWING:  Harmful or fatal if swallowed.

 

 

FIRST AID PROCEDURES:

 

SKIN:  Clean thoroughly with pumice-based hand cleaner, followed by soap and water.

EYES:  Flush with clear water for 15 minutes and seek medical attention immediately.

BREATHING:  Move victim to fresh air.  If asthmatic conditions occur, call a physician.

SWALLOWING:  DO NOT induce vomiting.  Seek medical attention immediately.

 

SECTION VI - REACTIVITY DATA                                                                                                               

 

STABILITY:  Stable

INCOMPATABILITY (MATERIALS TO AVOID):  Water (moisture); alcohols; amines; strong acids and bases.

HAZARDOUS DECOMPOSITION PRODUCTS:  Oxides or carbon and nitrogen.

HAZARDOUS POLYMERIZATION:  Will not occur.

CONDITIONS TO AVOID:  Excessive heat and/or wet conditions.  Will react with water to produce COČ

and exotherm.

 

SECTION VII - SPILL OR LEAK PROCEDURES                                                                                           

 

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:  Cover with a layer of sand

or other suitable absorbent.  Use protective measures as outlined under Section VIII below.  Avoid contact

with eyes, skin or clothing.

 

WASTE DISPOSAL METHOD:  Dispose of in accordance with local, state and federal regulations. 

Absorb with sand.

 

SECTION VIII - SPECIAL PROTECTION INFORMATION                                                                              

 

RESPIRATORY PROTECTION (SPECIFY TYPE):  In confined spaces, use fresh air hood or NIOSH certified

organic vapor canister unit.

EYE PROTECTION:  Safety goggles or face shield.

SKIN PROTECTION:  Nitrile rubber gloves.

OTHER PROTECTIVE EQUIPMENT:  Coveralls and/or rubber apron, rubber shoes or boots.

PERSONAL HYGIENE:  Wash thoroughly after applying this material.

 

SECTION IX - SPECIAL PRECAUTIONS                                                                                                     

 

PRECAUTIONS TO BE TAKEN IN HANDLING:  Avoid prolonged or repeated contact with skin. 

Avoid contact with moisture.  Do not use in confined areas without adequate ventilation.

 

SECTION X - TRANSPORTATION INFORMATION                                                                                       

 

PROPER SHIPPING NAME:  Paint

HAZARD CLASS:  3

PACKING GROUP:  III

ID #:  UN 1263

RQ:  None

TRANSPORT LABELS REQUIRED:  Flammable liquid.  (In the U.S., this material may be re-classified as a

combustible liquid and is not regulated in containers less than 119 gallons via surface transportation.)

 

 

This information accumulated herein is believed to be accurate but is not warranted to be, whether originating

with the company or not.  Recipients are advised to confirm, in advance of need, that the information is current,

applicable and suitable to their circumstances.

 

 

 

DATE ISSUED:  JANUARY 2005

 

Copyright Andek Corporation 2005.  All rights reserved.