MSDS (pdf)Print (pdf)

    
 
 

 
 
 
 
 
 
HOME
Roofing
Flooring & Deck
Specialty Surfaces
Flashband
Cocoon
Tools
Roofing Guide
FAQS
MSDS
Project Profiles
Project References
Partners & Links
Interesting Stuff
VOC Status
Chemical Resist Gde
Color Chart
Careers
Contact Us
Site Map
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

POLAFLOOR PD is an air drying, moisture cured, single component polyurethane coating for application to industrial concrete floors.  It produces a surface that is very wear-resistant and is unharmed by most industrial chemicals.  POLAFLOOR PD cures to an attractive semi-gloss finish and is available with aluminum oxide granules or sharp quartz silica to provide a highly traction-enhancing surface.

 

OUTSTANDING FEATURES:      

§         Fast setting; has rapid strength build

§         Develops high impact and thermal shock resistant properties

§         Protects floors from spalling, cracking or other forms of breakdown due to water attack

§         Long service life, even in industrial or chemical environment

§         Saves time, money and labor; reduces downtime of floor after application

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPECIFICATIONS:

Coating Type:     

Moisture-cured polyurethane

VOC:  

450 gms/liter

Pot Life: 

Single component

Shelf Life:      

6 months

Recommended Thickness:   

5 mils dry film thickness

Coverage:    

2 coats @ 360 square feet/gallon per coat

Packaging:

1 gallon and 5 gallon pails

Color:   

Concrete Gray or Tile Red

 

APPLICATION:

Caution! READ THIS ENTIRE DATA SHEET BEFORE CONTINUING.

 

All surfaces to be coated must be clean, dry and completely free of loose particles, oil, grease or any substance that would interfere with proper bond. Surfaces may be cleaned by emulsifiable degreaser, solvent, heavy duty detergent, sand blasting or other convenient form of surface preparation.  Remove all traces of cleaning agent and allow the surface to dry before beginning work.  Previously coated surfaces must be tested for soundness and compatibility with POLAFLOOR PD. It may be necessary to brush blast previous coatings to provide a key for proper bonding.           

 

POLAFLOOR PD may be applied by roller, brush or squeegee brush. If using a roller, a medium pile roller with a solvent-resistant pile and core is recommended. If using a brush, carry the POLAFLOOR PD to the surface on the brush. No moisture can be present on equipment or the substrate when using POLAFLOOR PD. Two coats are recommended for optimum appearance and durability.  Apply subsequent coats when the prior coat is touch dry, but not more than 24 hours between coats. If aggregate is used to increase traction, broadcast it into the first coat while it is still wet. Clean equipment immediately after use with xylene or toluene.  It is important that cleaning takes place before the Polafloor dries.

 

LIMITATIONS:

Do not use below 35°F.  Shelf life is 12 months when stored in factory sealed containers.  Coated surfaces with direct exposure to sunlight will experience a loss of gloss and a slight change in color.

 

PRECAUTIONS:

Warning!  This product is flammable.  Keep away from sparks and open flames.  Use manual spray equipment or EP (explosion proof) rated equipment.  Keep container tightly closed when not in use.  Do not ingest.  In case of ingestion, do NOT induce vomiting and seek immediate medical attention.  Keep away from skin and eyes with rubber gloves, full coveralls and eye goggles.  In case of contact, flush with clear water for 15 minutes.  In case of contact with eyes, seek immediate medical attention in addition to flushing.  Individuals with sensitivities to handling isocyanates are advised not to handle this product.

 

TECHNICAL DATA:

Flashpoint:    

105°F

SETA

Dry Density:

1.12 gms/cc

 

Dry Film Thickness: 

5 mils @ 180 square feet/gallon (2 coats)

Temperature Range:      

Operating temperatures of -50°F to 200°F will not affect performance. Occasional exposure to 250°F is tolerable.

Exterior Durability:   

Will not readily hydrolize or oxidize, strong sunlight will reduce the gloss.

Chemical Resistance:

Extremely good resistance to most chemicals including common solvents, brake fluids, fuels, alkalis and acids

 

 

 

NOTICE:  The information presented herein is based on tests and data that Andek Corporation believes to be reliable.  It is intended for use by technically qualified personnel at their own discretion and risk.  Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.  Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.

 

 

Copyright Andek Corporation 2007.  All rights reserved.