T Catalyst is a
metal chelate that is added to approved water based Andek coatings to
boost viscosity and adjust the rheological behavior to individual
application requirements.
T Catalyst will
thicken the coating to a paste or caulk-like consistency, enabling
the coating to be used for repairs, preparation work, and other
activities that require
a thickened material. T Catalyst
may be added in precise measured amounts to achieve the intended
characteristics required by the applicator.
OUTSTANDING FEATURES:
§ Provides the exact application control demanded by the
professional contractor
§ Allows exact color matching of detail and reinforcement material
with the entire coating application
§ Provides rheological adjustment to improve film thickness yield
on steep pitch profiles
§ Reacts rapidly to achieve target viscosity
§ Does not reduce pot life of the coating
§ Maintains excellent "wet edge" to accurately transition-in
patched areas
§ Ensures 100% compatibility of all products incorporated into the
coating system
SPECIFICATIONS:
Product Type: | Metal Chelate |
Pot Life: | Variable (See Limitations Section) |
Shelf Life: | 12 months |
Usage Ratio: | Variable (see Application Section) |
Packaging: | 1 quart or 1 gallon |
Color: | Transparent |
V.O.C. Content: | 400 grams/liter |
APPLICATION:
Caution! READ THIS ENTIRE DATA SHEET BEFORE CONTINUING.
Before use, also read the product data sheet for the product that is being combined with the T Catalyst.
T Catalyst may be incorporated into the following Andek products: Polaroof SP, Polaroof AC, Polaroof Firegard, Polagard, Polagard ‘S’, Polagard Fibre Lastic, and Polagard Flex-O-Tex. The use of T Catalyst with any other Andek product should be attempted only after thorough consultation with the Andek Technical Department. Add approximately 4 ounces of T Catalyst into a 5 gallon pail of Andek coating and stir slowly and thoroughly for about 3 minutes, using an Andek ProPower Mixer or similar effective mechanical device. Do not over-mix the product, as excessive shear will actually reduce the viscosity. After complete homogeneity has been achieved, let the mixture sit for approximately 5 minutes. This will allow trapped air bubbles to rise up and escape from the mixture and for the associative thickening effect to develop. If this viscosity is sufficient, then application may commence. If higher viscosity is required, add another 4 ounces of T Catalyst and repeat the procedure detailed above. Continue the process until the target rheology is achieved. Then apply the mixed coating, following the instructions on the coating container label. label.
LIMITATIONS:
T Catalyst will not affect the pot life of any product with which it is combined. Temperatures below 50°F (10°C) will delay the thickening process. Therefore, in colder weather, store both the Andek coating and the T Catalyst before use at 70°F (21°C) for faster thickening. Thickened coatings will not properly fill large gaps and voids as the shrinkage effect of drying may split the surface skin of the cured coating. Consequently, in these situations, Roofab reinforcing fabric should be used to provide maximum cohesive strength and dimensional integrity.
PRECAUTIONS:
Read and understand the entire T Catalyst M.S.D.S. before application. Also, read the M.S.D.S. for the product being combined with T Catalyst. This product contains alcohols and esters. Do not get in eyes or on skin or clothing. Wear standard safety equipment such as chemical splash goggles, rubber gloves, coveralls, and appropriate respirator when handling this product. Inhalation should be avoided. Persons with known respiratory allergies should avoid exposure to this product. In case of contact with eyes or skin, flush thoroughly with plenty of water for at least 15 minutes. If T Catalyst is inhaled, swallowed, or in the event of eye contact, get medical assistance immediately. Keep out of reach of children and pets.
TECHNICAL DATA:
Solids Content: | 60% (B.W.); 55% (B.V.) | ASTM D-1044 |
Viscosity (Average @ 70°F): | 600 cps | ASTM D-446 |
Flashpoint | Above 160°F | FTMS 141A |
V.O.C. Content: | 400 grams/liter | EPA Method 24 |
NOTICE: The information presented herein is based on tests and data that Andek Corporation believes to be reliable. It is intended for use by technically qualified personnel at their own discretion and risk. Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.
