WEARCOAT 44 is a two-component, aliphatic urethane coating that produces a tough, glossy, hard-wearing and chemically resistant surface. Abrasion-resistant and UV stable, WEARCOAT 44 will protect and beautify a variety of interior and exterior substrates. If necessary, a range of textured aggregates is available to provide a traction enhanced surface. Resistant to U.V. radiation providing excellent stability and color retention.

 

OUTSTANDING FEATURES:  

§         Can be used over concrete, wood, masonry, vinyl, steel and other approved surfaces

§         Produces a fully adhered, seamless, high density, urethane coating

§         Protects your investment by increasing the effective service life of the substrate

§         Is dustproof, and salt & chemical resistant

§         May be applied by brush, roller or airless spray

§         Resists penetration by oils, fuels and process fluids

§         Sets quickly and develops strength rapidly

§         Accommodates tire mounted vehicular traffic and eliminates bonding to paints

§         Scrubbable and easy to clean

§         Provides long term resistance to wear and abrasion

§         Ideal for horizontal, pitched and vertical surfaces

§         26 standard colors to choose from! Custom colors are also available

§         Also available in a clear formula (Clearcoat 44)   

§         Warrantied for 5 years

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SPECIFICATIONS:

Coating Type:	Two-part aliphatic urethane
VOC:	450 gms/liter
Pot Life:	3 hours @ 70°F (50% R.H.)
Shelf Life:	12 months
Recommended Thickness:	4 mils dry film thickness
Coverage:	2 coats @ 400 square feet/gallon per coat
Packaging:	1 gallon and 5 gallon pails
Color:	A variety of standard and custom colors

 

APPLICATION:

Caution! READ THIS ENTIRE DATA SHEET BEFORE CONTINUING.

 

All surfaces to be coated must be clean, dry and completely free of oil, grease, dust and any other substance that may interfere with proper bond.

 

Add Part B color concentrate to the clear Part A and stir thoroughly for 3 minutes.  WEARCOAT 44 may be applied by brush, roller or airless spray technique.  Apply at a rate of 400 square feet per gallon per coat.  Care must be taken to avoid creating foam or trapping air which may result in pinholes or hazing.                              

                                                                            

Tools and equipment may be cleaned with xylene. 

 

MAINTENANCE:                                                     

To repair damaged areas, coarse sanding should be followed by thorough cleaning with fresh water.  WEARCOAT 44 may then be reapplied to the clean, dry surface.

 

LIMITATIONS:

Store in a cool, dry place away from direct sunlight.  Avoid opened containers as moisture will cure the material.  Do not apply in temperatures below 35°F.  Application must be protected from precipitation for at least 4 hours.  Shelf life is 12 months when stored in proprietary sealed containers between 45°F and 85°F.

 

PRECAUTIONS:

During handling of this product, it is recommended that standard safety equipment such as rubber gloves, chemical splash goggles, and coveralls be worn.  Avoid contact with skin and eyes.  In case of contact, flush with clear water for 15 minutes.  In case of contact with eyes, get immediate medical attention in addition to flushing.  Do not ingest.  In case of ingestion, do NOT induce vomiting and seek immediate medical attention.  For additional information, contact our Technical Department.

 

TECHNICAL DATA:

Flashpoint:	110°F	FTMS 141A(M4293)
Shore 'A' Hardness:	95	ASTM D-2240
Tensile Strength:	4,500 lb/square inch	ASTM D-412
Elongation:	10%	ASTM D-412
Solids Content:	48% (B.W.); 44% (B.V.)	ASTM D-1044
Flexibility @ Low Temperature:	180 deg. bend @ 20°F	ASTM C-711
Impact Resistance (4mm indent.):	No cracking or loss of adhesion	BS3900 Part E3
Water Absorption:	Zero	ASTM D570-77
Working Time:	3 hours @ 70°F (50% R.H.
Drying Time:	1 1/2 hours @ 70°F (50% R.H.)
Cure Time:	24 hours @ 70°F (50% R.H.)
Exterior Durability:	Good resistance to UV and harsh weather extremes

 

 

 

NOTICE:  The information presented herein is based on tests and data that Andek Corporation believes to be reliable.  It is intended for use by technically qualified personnel at their own discretion and risk.  Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.  Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.

 

 

Copyright Andek Corporation 2008.  All rights reserved.