SPECIFICATIONS:
Coating Type: | Two-part aliphatic urethane |
VOC: | 320 gms/liter |
Pot Life: | 3 hours @ 70°F (50% R.H.) |
Shelf Life: | 12 months |
Recommended Thickness: | 3 mils dry film thickness per coat |
Coverage (normal): | 2 coats @ 400 square feet/gallon per coat |
Coverage (with coarse aggregate) | 2 coats @ 300 square feet/gallon per coat |
Packaging: | 1 gallon and 5 gallon pails |
Color: | A variety of standard and custom colors |
APPLICATION:
Caution! READ THIS ENTIRE DATA SHEET BEFORE CONTINUING.
All surfaces to be coated must be clean, dry, and completely free of loose particles, oil, grease, or any substance that would interfere with proper bond. WEARCOAT
66 may be applied over products such as Polafloor Epoxy High Build at any time after the surface has been thoroughly set for at least 1 hour. If overcoating a painted surface, check compatibility first, as some paints may bleed color or be lifted by solvents.
Add Part ‘B’ color concentrate to the clear Part ‘A’ and stir thoroughly for 3 minutes. WEARCOAT
66 is applied at a rate of 400 square feet per gallon per coat.
WEARCOAT
66 may be applied by brush, roller, or airless spray technique in a thin, even coat. If traction enhancement is required, iron-free sharp white quartz sand or any approved aggregate may be broadcast into the wet WEARCOAT
66. After the first coat has thoroughly dried with the embedded aggregate, a second coat of WEARCOAT
66 is applied to thoroughly encapsulate the aggregate. Sized and graded sharp white quartz sand and coarse Estes aggregate are available from Andek Corporation. Equipment may be cleaned with toluene or xylene while the WEARCOAT
66 is still wet.
MAINTENANCE:
To repair damaged areas, coarse sanding should be followed by thorough cleaning with fresh water. WEARCOAT
66 may then be reapplied to the clean, dry surface.
LIMITATIONS:
Store in a cool, dry place away from direct sunlight. Avoid opened containers as moisture will cure the material. Do not apply in temperatures below 35°F. Application must be protected from precipitation for at least 4 hours. Shelf life is 12 months when stored in proprietary sealed containers between 45°F and 85°F.
PRECAUTIONS:
During handling of this product, it is recommended that standard safety equipment such as rubber gloves, chemical splash goggles, and coveralls be worn. Avoid contact with skin & eyes. In case of contact, flush with water for 15 minutes. In case of contact with eyes, get immediate medical attention in addition to flushing. Do not ingest. In case of ingestion, do NOT induce vomiting and seek medical attention.
For additional information, contact Andek’s Technical Department.
TECHNICAL DATA:
Resistance to Corrosion: | 10 | ASTM D-1654 |
Shore ‘A’ Hardness: | 95 | ASTM D-2240 |
Tensile Strength: | 4,500 lb/square inch | ASTM D-412 |
Elongation: | 10% | ASTM D-412 |
Solids Content: | 48% (B.W.); 66% (B.V.) | ASTM D-1044 |
Flashpoint: | 110°F | FTMS 141A (M4293) |
Flexibility @ Low Temperature: | 180 deg. bend @ 20°F | ASTM C-711 |
Impact Resistance: | 4mm indent | ASTM D-1474 |
Water Absorption: | Zero | ASTM D570-77 |
Working Time: | 3 hours @ 70°F (50% R.H.) | |
Drying Time: | 1 1/2 hours @ 70°F (50% R.H.) | |
Cure Time: | 24 hours @ 70°F (50% R.H.) | |
Weatherometer (5000 hours) | Pass | ASTM G-23 |
NOTICE: The information presented herein is based on tests and data that Andek Corporation believes to be reliable. It is intended for use by technically qualified personnel at their own discretion and risk. Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.
Copyright Andek Corporation 2008. All rights reserved.
