POLAFLOOR P.U.R. BRUSHABLE

DESCRIPTION:

POLAFLOOR P.U.R. BRUSHABLE combines the properties of silicon carbide, Kevlar *, and urethane chemistry to produce a high-performance engineered coating. An ultra-high performance three-part urethane floor coating, it is designed for the most severe interior and exterior service. POLAFLOOR P.U.R. BRUSHABLE has exceptional resistance to most industrial chemicals and provides a tough, wear-resistant surface that resists both impact and abrasion.

• Highly impermeable to fluids

• Resists the leaching of chemicals through the coating

• Easy to clean yet provides traction enhancement

• Suitable for industrial floors, tanks, pits, gullies and secondary containment areas

• Stands up to vehicular traffic and diverse industrial activities

• Produces a hard, lightly textured surface

Coating Type:     Kevlar* Modified Urethane

VOC:                   Zero

Pot Life:             40 minutes @ 70 F

Shelf Life:           12 months

Recommended Thickness: 20 mils dry film thickness

Coverage:            50 square feet/unit

Packaging:           20 pound unit

Color:                  Black

*DuPont's Registered Trademark

ANDEK CORPORATION

P.O. Box 392, 850 Glen Avenue

Moorestown, NJ 08057-0392 USA

Tel: 856-786-6900 Fax: 856-786-0580

©ANDEK CORPORATION, 1999. ALL RIGHTS RESERVED.

POLAFLOOR  P.U.R.  BRUSHABLE

APPLICATION:                                                                                   LIMITATIONS:

Caution!  READ THIS ENTIRE DATA SHEET                 Do not apply to frozen or damp surfaces.  Do

BEFORE CONTINUING.                                                         not apply if the application cannot be pro-

All surfaces to be coated must be clean, dry                           tected from precipitation for at least 4 hours

and completely free of loose particles, oils,                            Full chemical resistance properties are not

grease, or any substance that would inter-                              achieved until 5 days after application.  Foot

fere with proper bond.  All preparation work                          traffic may not resume until 24 hours after

including substrate repairs and expansion                              application.  Only skilled coating applicators

joints must be completed prior to applica-                              should use this product.

tion.  If PUR Brushable is to be applied over

a waterproofing membrane, the membrane                                  MAINTENANCE:

should be thoroughly inspected to insure

that it has completely set and is devoid of                              If an area of PUR Brushable becomes damaged,

pinholes or interruptions.  Add the Part A                              it should be mechanically removed down to the

to the Part B while stirring thoroughly with                        substrate.  The edges surrounding the patch     

a drill-type stirrer.  Mixing must be continued                        should be sanded & primed with Polaprime 21

for 3 minutes total.  The mix should then be                           and new PUR Brushable may be applied.

poured back and forth between the two com-

ponent cans twice, then stirred a further min-                              PRECAUTIONS:

ute.  The Part C should be stirred into the

mixture immediately and stirred for 2 min-                             Before using, read M.S.D.S. thoroughly.  During

utes until a uniform paste consistency is                                 handling of this product, use full coveralls,

achieved.  Careful attention to detail will                               rubber gloves and chemical splash goggles. 

help to produce the desired result in appear-                           During mixing, particle/dust masks should be

ance and performance.  Once mixed, PUR                               worn.   Do not ingest.  In case of ingestion, do

Brushable has approximately 40 minutes                               NOT induce vomiting and seek medical atten-

working time at 70 F and will have devel-                              tion immediately.  Avoid contact with skin and

oped an initial cure suitable for foot traffic                             eyes; in case of contact, flush with clear water     

within 24 hours.  The floor may be placed                                for 15 minutes.  For contact with eyes, seek

into full service within 48 hours.  Equipment                        immediate medical attention in addition to

may be cleaned with toluene, xylene or                                      flushing.  Keep out of reach of children and

atomatic naptha before the PUR Brushable                           pets.

has hardened.

TECHNICAL DATA:

Compressive Strength                                12,060 psi                                   ASTM C-109

Tensile Strength                                         2,685 psi                                   ASTM C-109

Linear Heat Expansion                               2.6 - 10 K                                     ITR (DIN) 

Heat Conductivity                                        0.97 W/K.M.                               ITR (DIN)

Grinding Wear                                              10.3 cm3                                     ITR (DIN

Water Vapor Transmission                          0.75 gms/M2/hr (=0.05 perms)    ASTM E-96

Chemical Resistance                                   See Polafloor PUR Report  #1

VOC Content                                                  Zero                                             ASTM D-1044

NOTICE:  The information presented herein is based on tests and data that Andek Corporation believes to be reliable.  It is intended for use by technically qualified personnel at their own discretion and risk.  Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.  Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.