POLAGARD 1047

DESCRIPTION:

POLAGARD 1047 is a high quality resin-based elastomeric wall coating material with waterproofing properties. It produces a permanently flexible coating to bridge hairline cracks and withstand thermal movement in a substrate. POLAGARD 1047 provides a satin type finish that is architecturally enhancing, long-lasting and weatherproof.

 

OUTSTANDING FEATURES:

 

  • May be applied to damp surfaces; won't wash off in sudden rain

  • Resists UV, mildew and chemical attack; has excellent alkali and chalking resistance

  • Protects the substrate from water damage, moves with thermal changes

  • Remains flexible, tough and waterproof

  • Possesses a 10-year life expectancy and a 5-year guarantee

  • Stores easily; safe and convenient to handle, apply and clean up

  • Can be applied during difficult, uncertain weather conditions

 

SPECIFICATIONS:

 

Coating Type:     Resin-based elastomeric

VOC:                  250 gms/liter

Pot Life:             Single component

Shelf Life:          12 months

Recommended Thickness: 18 mils dry film thickness

Coverage:          2 coats @ 125 square feet/gallon

Packaging:         5 gallon pails

Color:                White and other colors

 

 

ANDEK CORPORATION

P.O. Box 392, 850 Glen Avenue

Moorestown, NJ 08057-0392 USA

Tel: 856-786-6900 Fax: 856-786-0580

ŠANDEK CORPORATION, 1999. ALL RIGHTS RESERVED.

 

POLAGARD   1047

 

APPLICATION:                                                                            APPLICATION (cont'd):

Caution! READ THIS ENTIRE DATA SHEET                       roll the first coat to eliminate small voids or  

BEFORE CONTINUING.                                                             pocks at the surface.  Polagard 1047 may be

Surface must be firm and free of loose debris,                          thinned with no more than 4 oz. of mineral

dirt, grease, oil, mildew, or any substance that                           spirit per gallon if necessary.  Apply Polagard

may interfere with bond.  All cracks larger                                1047 in 2 coats at a wet thickness of about 12

than 1/32" need to be filled with a good grade                           mils per coat.  Apply the second coat after the

acrylic caulk.  All other types of repairs or                                   first coat has set (about 4-6 hours).  Do not

patches must be made prior to coating as well.                           apply to frozen surfaces.  Backrolling or re-

Allow repairs to cure before beginning appli-                               touching areas that have begun to dry may

cation.  Surface may be damp but not wet.  An                            peel the coating. 

overly damp surface may promote runs or sags.                       

 

Wall Substrate Priming Requirements:                                      MAINTENANCE:

SUBSTRATE                                     PRIMER

Highly porous surfaces                 Polaprime 2                       If a surface becomes dirty, spray with a mild

Copper, brass, tin, lead &                                                            soapy water solution and rinse with clear water.

oxidized metal                               Polaprime 21                      Do not use high pressure spray or solvents.  For

Painted metals or galvalume     Polaprime 3                       harder to clean areas or damaged coating, re-

All other substrates                      No primer                            coat with Polagard 1047.

 

It is advisable to test previously coated or treat-                   PRECAUTIONS:

ed surfaces by first applying Polagard 1047 to a

4'x4' area and allow it to cure.  Later, inspect                    Polagard 1047 is a resin based product.  Avoid

the test area for adhesion, voids or sags.  It may                    contact with skin and eyes.  In case of contact,

be necessary to sand or rough previously paint-                      immediately flush with clear water.  For eyes,

ed surfaces to improve bond performance.                              get medical attention in addition to flushing.

                                                                                                      Avoid inhalation of spray mist.  If spray mist is

Polagard 1047 is applied straight out of the can                  inhaled, seek immediate medical attention.  In

after 2 minutes of low speed stirring or mixing.                    case of ingestion, do NOT induce vomiting and

Apply the product using a brush, roller or spray                       immediately contact a physician.  Wear rubber

technique.  For airless spray application, use                          gloves, coveralls and safety goggles when apply-

equipment similar to a 30:1 ratio Graco with a                      ing Polagard 1047.

#36 tip.  When spraying, it is advisable to back-

 

TECHNICAL DATA:

Moisture Vapor Transmission                             1.23 perms                     ASTM E-96

Elongation                                                             65%                               ASTM D-412

Tensile Strength                                                 250 psi                          ASTM D-412

Weatherometer (3000 hours)                            Pass                                ASTM G-23

Shore 'A' Hardness                                              42 deg.                           ASTM D-2240

Viscosity @ 70 F                                                  4500 cps                       ASTM D-446

Cleaning of equipment                                         Mineral Spirit

NOTICE:  The information presented herein is based on tests and data that Andek Corporation believes to be reliable.  It is intended for use by technically qualified personnel at their own discretion and risk.  Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.  Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.