RUBBERKOTE 1047

DESCRIPTION:

RUBBERKOTE 1047 is a revolutionary waterproofing coating that is uniquely designed to be applied to wet or damp roofs where curing will proceed even underwater! Yet unlike quick patch materials that have a short life expectancy, Rubberkote 1047 is guaranteed to last for five years! Rubberkote 1047 will adhere to all common roofing substrates and is ideal for either instant roof repairs or as a permanent roof coating.

 

OUTSTANDING FEATURES:

 

  • Exhibits good adhesion to asphalt, coal tar, B.U.R., zinc, tin, steel, aluminum, capsheet, modified, concrete, and transite. 

  • Will cure underwater regardless of applied coating thickness instantly seals leaking roofs.

  • Remains flexible at low temperatures and will not flow at high roof temperatures.

  • A user-friendly material that results in quick and easy application.

 

SPECIFICATIONS:

 

Coating Type:     Resin-based, air drying

VOC:                  400 gms/liter

Pot Life:             Single component

Shelf Life:          12 months

Recommended Thickness: 30 mils dry film thickness

Coverage:           30 - 40 square feet per gallon

Packaging:          3.5 gallon pails

Color:                  Light gray

 

 

ANDEK CORPORATION 

850 Glen Avenue, P.O. Box 392,

Moorestown, NJ 08057-0392 USA

Tel: 856-786-6900 Fax: 856-786-0580 Website: www.Andek.com

©2001 ANDEK CORPORATION. ALL RIGHTS RESERVED.

 

 

RUBBERKOTE  1047

 

APPLICATION:                                                                                   LIMITATIONS:

Caution!  READ THIS ENTIRE DATA SHEET BEFORE    Not recommended in areas of high chemical attack  

CONTINUING.                                                                                 (around stacks, etc.).

Although only minimal preparation is required, all loose

material, stones and grease should be removed, together               MAINTENANCE:

with as much dust, rust and standing water as is reason-

ably possible.  All holes, gaps and joints should be                         Damaged areas may be repaired by re-application of

bridged with Roofab sandwiched between sufficient Rubber-   Rubberkote 1047.

kote 1047 to provide thorough wetting of the roof surface

and thorough saturation of the Roofab.  This is best ac-                 PRECAUTIONS:

complished by "stippling in" with a brush.

Rubberkote 1047 may be applied in 2 coats of 20 wet           Contains solvents.  Read M.S.D.S. thoroughly before

mils thickness each over capsheet, modified, metal, trans-    using.  Do not get on skin or in eyes.  Do not ingest

ite or concrete after the above preparation is complete.         or inhale vapor.  Make sure that vapor does not enter

The 1st coat may be applied directly over any fresh, wet        building.  If skin is contaminated, use suitable cleaner.

repairs as curing will proceed regardless of thickness al-     If eyes are contaminated, wash with water and seek

though slower.  The 2nd coat may be applied as soon as       medical attention.  If clothing is contaminated, discard.

the 1st coat is sufficiently dry to walk on (normally 2-3     If ingested, do NOT induce vomiting and seek immediate

days at 65 F).  Care should be taken not to disturb any       medical attention.  If inhaled, remove person to fresh

patches or pre-treatments as they may still be wet.             air. 

Rubberkote 1047 may be applied over asphalt or coal

tar B.U.R. after the preparation described above has been     CAUTION:  KEEP OUT OF REACH OF CHILDREN

completed.  The 1st coat should be applied at 66 square          AND PETS.

feet per gallon; Roofab laid into it and thoroughly

"stippled in" by brush with a 2nd coat at 66 square feet       For further information, please contact our Technical

per gallon to remove all tents and voids.  The Roofab              Department.

should be overlapped as indicated by the laplines and

thoroughly saturated with Rubberkote 1047 so that no

dry spots remain.

 

TECHNICAL DATA:

Moisture Vapor Transmission                             0.32 perms                                                     ASTM E96

Tensile Strength                                                 250 psi                                                            ASTM D-412

Elongation                                                             65%                                                                 ASTM D-412

Flexibility at Low Temperature                         180 degree bend @ -20 C                               ASTM C-711

Shore 'A' Hardness                                              36 degrees                                                       ASTM D-2240

Puncture Resistance                                            50 psi                                                               ASTM D-154-79

Viscosity @ 70 F                                                  10,000 cps                                                         ASTM D-446

Drying Time @ 80 F (70% R.H.)                       60 hours (to walk on)                                           

Total Cure @ 80 F (70% R.H.)                          7 days (to 36 degrees Shore 'A')

Application Equipment                                       Brush, roller, or spray

Cleaning of Equipment                                       Mineral Spirits

 

NOTICE:  The information presented herein is based on tests and data that Andek Corporation believes to be reliable.  It is intended for use by technically qualified personnel at their own discretion and risk.  Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information.